The coding and connector gender decide the fit
M12 power cables look similar, but the coding (T, L or S) and the connector gender on each end determine whether a cable will mate with your device and how it integrates into your panel. The three Innov8 cables below share a 1 m length and a PUR jacket rated for drag chains, but they differ in connector type and termination. Start by checking the port on your equipment and the wiring method you plan to use.
T-code, L-code, S-code: what each cable offers
All three are unshielded 4-pin power cables with a PUR jacket suitable for drag chain use. The table highlights the key differences in connectors and termination.
- M12 T-Code 4-Pin Female to Open Wire (2428391): T-coded female connector on one end, open power wires on the other. Intended for industrial power distribution and automation, including robotics, drives and control systems. Open termination allows direct wiring into control panels or custom assemblies.
- M12 L-Code 4-Pin Female to Open Wire (2428392): L-coded female connector on one end, open power wires on the other. Commonly used for high-current power delivery to motors, drives, I/O modules and industrial equipment. Open termination for terminals, controllers or custom electrical assemblies.
- M12 S-Code 4-Pin Male to Female (2428393): S-coded male and female connectors on both ends, with a 3 + PE contact configuration. Commonly used for AC power distribution to motors, drives and control equipment. No open wires; this is a complete male-to-female extension or connection cable.
Connector and termination details for the open-wire cables
- M12 T-Code 4-Pin Female to Open Wire Power Cable 1m – PUR Drag Chain: M12 T-Code 4-pin female connector to open wire power leads, PUR jacket, unshielded, drag chain suitable. The T-code female connector mates with a T-coded male port; the open wires let you terminate directly into a terminal block or controller.

M12 T-Code 4-Pin Female to Open Wire Power Cable 1m – PUR Drag Chain - M12 L-Code 4-Pin Female to Open Wire Power Cable 1m – PUR Drag Chain: M12 L-Code 4-pin female connector to open wire power leads, PUR jacket, unshielded, drag chain suitable. The L-code female connector mates with an L-coded male port; open wires allow quick installation into terminals, controllers or custom assemblies.

M12 L-Code 4-Pin Female to Open Wire Power Cable 1m – PUR Drag Chain
S-code brings its own contact configuration
Unlike the T-code and L-code cables above, the S-code cable is a male-to-female assembly with a 3 + PE contact configuration. That means it provides three power contacts plus a protective earth connection. If your device has an S-coded female port and you need to extend or connect to another S-coded male port, this cable is the direct fit. It does not have open wires, so it is not intended for panel wiring where bare leads are required.
S-code cable evidence
- M12 S-Code 4-Pin Male to Female Power Cable 1m – PUR Drag Chain Industrial: M12 S-Code 4-pin male to female connectors, straight design, 3 + PE contact configuration, PUR jacket, unshielded, drag chain suitable. The 3 + PE configuration and male-to-female ends make this cable suited to AC power distribution between S-coded devices, not to open-wire panel termination.
How to choose between the three
Use the port on your equipment and your wiring method as the deciding factors.
- Your device has a T-coded male port and you need to wire into a terminal block: Choose the T-code female to open wire cable (2428391).
- Your device has an L-coded male port and you need to wire into a terminal block: Choose the L-code female to open wire cable (2428392).
- You need to connect two S-coded devices (male to female) without open wiring: Choose the S-code male to female cable (2428393).
- Your device uses a different coding or gender: None of these cables will mate correctly; check the port on your equipment before ordering.
What the supplied information does not confirm
The catalog records do not state current ratings, voltage ratings, conductor size, pin assignments or temperature limits for any of these cables. They also do not confirm compatibility with specific devices beyond the coding and gender described. For critical power installations, verify these details against the equipment manufacturer's specifications and the cable's full datasheet before commissioning. The absence of this data in the supplied information is not evidence that the cables lack such ratings; it simply means they are not confirmed here.




